Dev/OPi/OPiZero: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
m (Drizzt moved page Dev/OPi/OpiZero to Dev/OPi/OPiZero without leaving a redirect) |
(No difference)
|
Revision as of 18:53, 15 October 2019
Description
Official website : http://www.orangepi.org/orangepizero/ (Backup)
The OrangePi Zero board is an Open-source Single Board Computer (SBC) of 48x46mm created and sold by Xunlong.
Base system
- Create initial system from scratch (sources): all the steps, using u-boot and Linux kernel sources, and a guide to create a minimal system using either Busybox or Devuan.
- The "SD card creation" section from the "from scratch" page also provides information to use the u-boot, kernel image, and Devuan root filesystem I built.
You can get the images here: Images for Orange Pi Zero board.
Connection and startup
USB-UART serial console connection
On the J3 connector (3 pins male 2.54mm, next to the Ethernet connector, pin 1 on the board edge) :
- pin 1 - GND : Black
- pin 2 - UART RX : Orange
- pin 3 : UART TX : Yellow
SD card boot
The OrangePi Zero board boots from the SD card which has to be prepared following specific steps. Follow the "SD card creation" section from the "from scratch" page
Extension ports
The OrangePi Zero board has two extension ports using common 2.54mm (0.1inch) pitch:
- con4 : 2x13
- con5 : 1x13
con4 : 2x13 Header | |||
---|---|---|---|
1 | 3.3V | 2 | 5V |
3 | TWI0_SDA / PA12 / GPIO12 | 4 | 5V |
5 | TWI0_SCK / PA11 / GPIO11 | 6 | GND |
7 | PWM1 / PA06 / GPIO6 | 8 | UART1_TX / PG06 / GPIO198 |
9 | GND | 10 | UART1_RX / PG07 / GPIO199 |
11 | UART2_RX / PA01 / GPIO1 | 12 | SIM_CLK/PA_EINT7 / PA07 / GPIO7 |
13 | UART2_TX / PA00 / GPIO0 | 14 | GND |
15 | UART2_CTS / PA03 / GPIO3 | 16 | TWI1-SDA / PA19 / GPIO19 |
17 | 3.3V | 18 | TWI1-SCK / PA18 / GPIO18 |
19 | SPI1_MOSI / PA15 / GPIO15 | 20 | GND |
21 | SPI1_MISO / PA16 / GPIO16 | 22 | UART2_RTS / PA02 / GPIO2 |
23 | SPI1_CLK / PA14 / GPIO14 | 24 | SPI1_CS / PA13 / GPIO13 |
25 | GND | 26 | SIM_DET/PA_EINT10 / PA10 / GPIO10 |
con5 1x13 Header | |
---|---|
1 | 5V |
2 | GND |
3 | USB-DM2 |
4 | USB-DP2 |
5 | USB-DM3 |
6 | USB-DP3 |
7 | LINEOUTR |
8 | LINEOUTL |
9 | TV-OUT |
10 | MIC-BIAS |
11 | MIC1P |
12 | MIC1N |
13 | CIR-RX |
External links
(Pseudo)random list of links to pages with information to compile u-boot, the Linux kernel, and create a root filesystem.
- Xunlong Orange Pi Wiki : http://www.orangepi.org/Docs/mainpage.html
- Xunlong Orange Pi Github : https://github.com/orangepi-xunlong/OrangePi_Build
- Linux Sunxi Wiki : Orange Pi Zero(open source software community dedicated to providing open source operating system support for Allwinner SoC based devices).
- FreeBSD : https://wiki.freebsd.org/FreeBSD/arm/Allwinner
- Armbian : https://www.armbian.com/orange-pi-zero/