Drizzt at 00:54, 12 August 2022

2022-08-12T00:54:44Z

← Older revision		Revision as of 02:54, 12 August 2022
Line 11:		Line 11:
	* The "SD card creation" section from the [[Dev/OPi/OPiZeroPlus/From_Scratch\|"from scratch" page]] also provides information to use the u-boot, kernel image, and Devuan root filesystem I built. <br />		* The "SD card creation" section from the [[Dev/OPi/OPiZeroPlus/From_Scratch\|"from scratch" page]] also provides information to use the u-boot, kernel image, and Devuan root filesystem I built. <br />
	You can get the images here: [http://data.nathael.net/Dev/OPi/OPiZeroPlus/ Images for Orange Pi Zero Plus board].		You can get the images here: [http://data.nathael.net/Dev/OPi/OPiZeroPlus/ Images for Orange Pi Zero Plus board].

			== Onboard Wifi ==
			Currently testing informations from [https://linux-sunxi.org/Wifi#SDIO-based Sunxi wiki].

			git clone https://github.com/jwrdegoede/rtl8189ES_linux.git
			cd rtl8189ES_linux.git
			git checkout -B rtl8189fs origin/rtl8189fs
			make -j8 ARCH=arm64 CROSS_COMPILE=aarch64-linux-gnu- KSRC=../Build/vanilla/

	== Connection and startup ==		== Connection and startup ==

Drizzt: Created page with "{{DISPLAYTITLE:Orange Pi Zero Plus}} == Description == Official website : https://orangepi.com/index.php?route=product/product&product_id=848 The "OrangePi Zero Plus" board..."

2022-07-24T17:20:31Z

Created page with "{{DISPLAYTITLE:Orange Pi Zero Plus}} == Description == Official website : https://orangepi.com/index.php?route=product/product&product_id=848 The "OrangePi Zero Plus" board..."

New page

{{DISPLAYTITLE:Orange Pi Zero Plus}}

== Description ==
Official website : https://orangepi.com/index.php?route=product/product&product_id=848

The "OrangePi Zero Plus" board is an Open-source Single Board Computer (SBC) of 48x46mm created and sold by Xunlong.

== Base system ==
* [[Dev/OPi/OPiZeroPlus/From_Scratch|Create initial system from scratch (sources)]]: all the steps, using u-boot and Linux kernel sources.
* [[Dev/Embedded/Rootfs|Rootfs guide]] to create either a minimal system using Busybox or a full Devuan GNU/Linux system.
* The "SD card creation" section from the [[Dev/OPi/OPiZeroPlus/From_Scratch|"from scratch" page]] also provides information to use the u-boot, kernel image, and Devuan root filesystem I built. <br />
You can get the images here: [http://data.nathael.net/Dev/OPi/OPiZeroPlus/ Images for Orange Pi Zero Plus board].

== Connection and startup ==
==== USB-UART serial console connection ====
[[File:OPi_Zero_UART.jpg|150px|thumbnail|UART debug port]]

On the J3 connector (3 pins male 2.54mm, next to the Ethernet connector, pin 1 on the board edge) :
: pin 1 - GND : Black
: pin 2 - UART RX : Orange
: pin 3 : UART TX : Yellow

==== SD card boot ====
The OrangePi Zero board boots from the SD card which has to be prepared following specific steps. Follow the "SD card creation" section from the [[Dev/OPi/OPiZeroPlus/From_Scratch|"from scratch" page]]

== Extension ports ==
The OrangePi Zero Plus board has two extension ports using common 2.54mm (0.1inch) pitch:
* con4 : 2x13
* con5 : 1x13

[[File:Orange_Pi_Zero_Plus_Expansion_Header.jpg|300px|thumbnail|Orange Pi Zero Plus Expansion Header]]

{| class="wikitable" style="width:550px;"
! colspan=4 | con4 : 2x13 Header
|-
| 1 || ''3.3V''
| 2 || ''5V''
|-
| 3 || TWI0_SDA / PA12 / GPIO12
| 4 || ''5V''
|-
| 5 || TWI0_SCK / PA11 / GPIO11
| 6 || ''GND''
|-
| 7 || PWM1 / PA06 / GPIO6
| 8 || UART1_TX / PG06 / GPIO198
|-
| 9 || ''GND''
| 10 || UART1_RX / PG07 / GPIO199
|-
| 11 || UART2_RX / PA01 / GPIO1
| 12 || SIM_CLK/PA_EINT7 / PA07 / GPIO7
|-
| 13 || UART2_TX / PA00 / GPIO0
| 14 || ''GND''
|-
| 15 || UART2_CTS / PA03 / GPIO3
| 16 || TWI1-SDA / PA19 / GPIO19
|-
| 17 || ''3.3V''
| 18 || TWI1-SCK / PA18 / GPIO18
|-
| 19 || SPI1_MOSI / PA15 / GPIO15
| 20 || ''GND''
|-
| 21 || SPI1_MISO / PA16 / GPIO16
| 22 || UART2_RTS / PA02 / GPIO2
|-
| 23 || SPI1_CLK / PA14 / GPIO14
| 24 || SPI1_CS / PA13 / GPIO13
|-
| 25 || ''GND''
| 26 || SIM_DET/PA_EINT10 / PA10 / GPIO10
|}

{| class="wikitable" style="width:300px;"
! colspan=2 | con5 1x13 Header
|-
| 1 || ''5V''
|-
| 2 || ''GND''
|-
| 3 || USB-DM2
|-
| 4 || USB-DP2
|-
| 5 || USB-DM3
|-
| 6 || USB-DP3
|-
| 7 || LINEOUTR
|-
| 8 || LINEOUTL
|-
| 9 || TV-OUT
|-
| 10 || MIC-BIAS
|-
| 11 || MIC1P
|-
| 12 || MIC1N
|-
| 13 || CIR-RX
|}

== External links ==
(Pseudo)random list of links to pages with information to compile u-boot, the Linux kernel, and create a root filesystem.
* Xunlong Orange Pi Github : https://github.com/orangepi-xunlong/OrangePi_Build
* [http://linux-sunxi.org/Main_Page Linux Sunxi Wiki] : [https://linux-sunxi.org/Xunlong_Orange_Pi_Zero_Plus Orange Pi Zero Plus](open source software community dedicated to providing open source operating system support for Allwinner SoC based devices).
** [http://linux-sunxi.org/Bootable_SD_card Linux Sunxi Wiki : Bootable SD Card]
** [http://linux-sunxi.org/Mainline_U-Boot Linux Sunxi Wiki : Mainline U-Boot]
** [http://linux-sunxi.org/Mainline_Kernel_Howto Linux Sunxi Wiki : Mainline Kernel Howto]
* FreeBSD : https://wiki.freebsd.org/FreeBSD/arm/Allwinner
* Armbian : https://www.armbian.com/orange-pi-zero/

Dev/OPi/OPiZeroPlus - Revision history

Drizzt at 00:54, 12 August 2022

Drizzt: Created page with "{{DISPLAYTITLE:Orange Pi Zero Plus}} == Description == Official website : https://orangepi.com/index.php?route=product/product&product_id=848 The "OrangePi Zero Plus" board..."